Gateway 2n per SMS finalmente!!!

Ciao, sono lieto di annunciarvi la disponibilità di un software realizzato da noi per interfacciarsi agli ottimi gateway telefonci 2n voiceblue.

Come alcuni di voi sicuramente sapranno, i Gateway Voiceblue 2n non hanno un modo “semplice” nè tantomeno “efficiente” per inviare sms sfruttando le sim inserite. Per risolvere queste ed altre lacune nella loro modalità diinvio, abbiamo realizzato un sms server che si interfaccia con i vari gateway presenti in rete e sfrutta al massimo le potenzialità delle sim inserite all’interno.

Tra le caratteristiche: impostazione soglia per sim (settimanale, giornaliera, mensile), impostazione numero sim, numero gateway, utenti e gruppi, possibilità di import in csv ed altro…

da non dimenticare che non richiede l’acquisto di software aggiuntivi da 2n

per info contattatemi

Trixbox 2.4 and EICON DIVA SERVER ***FINAL***

how to install an Eicon Diva server 4 bri in the last Trixbox version

if you need assistance I can provide a standard flat installation of this board at 75 €

yum install kernel-devel isdn4k-utils-devel gcc gcc-c++ asterisk-devel
ln -s /usr/src/kernels/2.6.18-53.1.4.el5-i686/ /usr/src/linux

wget http://www.dialogic.com/download/p/linux/source.2/107-83/DivaServer4Linux_installer_8.3-107-83.bin
sh DivaServer4Linux_installer_8.3-107-83.bin
cd /usr/lib/eicon/divas/src
./Build
cd ..
./Config
./Start
cd /usr/src/
wget ftp://ftp.chan-capi.org/chan-capi/chan_capi-1.0.2.tar.gz
tar -zxvf chan_capi-1.0.2.tar.gz

cd chan_capi-1.0.2
make install
nano /etc/asterisk/modules.conf and add chan_capi.so
nano /etc/asterisk/capi.conf

; CAPI config
;
;
[general]
nationalprefix=0
internationalprefix=00
rxgain=0.8
txgain=0.8
; If you are in Europe/Australia use alaw. Use ulaw otherwise
alaw=yes
[V4BRI-1]
;Define CAPI Controller 1 of V-4BRI-8M
;mode=immediate
isdnmode=DID
;ntmode=yes
incomingmsn=*
controller=1
softdtmf=0
accountcode=
context=from-pstn
group=1
callgroup=1
echocancel=yes
devices=2
[V4BRI-2]
;Define CAPI Controller 2 of V-4BRI-8M
;mode=immediate
isdnmode=DID
;ntmode=yes
incomingmsn=*
controller=2
softdtmf=0
accountcode=
context=from-pstn
group=1
callgroup=1
echocancel=yes
devices=2^
[V4BRI-3]
;Define CAPI Controller 3 of V-4BRI-8M
;mode=immediate
isdnmode=DID
;ntmode=yes
incomingmsn=*
controller=3
softdtmf=0
accountcode=
context=from-pstn
group=1
callgroup=1
echocancel=yes
devices=2^
[V4BRI-4]
;Define CAPI Controller 4 of V-4BRI-8M
;mode=immediate
isdnmode=DID
;ntmode=yes
incomingmsn=*
controller=4
softdtmf=0
accountcode=
context=from-pstn
group=1
callgroup=1
echocancel=yes
devices=2^

_______________________

trixbox and isdn bristuffed

how to install hfc card

 

after unload asterisk and amportal whit

amportal stop

 

type “setup”

unselect zaptel in system service…

and set the lan

 

—>reboot<— data-blogger-escaped-br=”br”>
cd /usr/src/kernels/2.6.9-34.0.1.EL-i686/include/linux
mv spinlock.h spinlock.h.old
wget http://nerdvittles.com/trixbox/spinlock.h

—>reboot<— data-blogger-escaped-br=”br”>
cd /usr/src
wget http://www.junghanns.net/downloads/bristuff-0.3.0-PRE-1q.tar.gz
tar -zxvf bristuff-0.3.0-PRE-1q.tar.gz
cd bristuff-0.3.0-PRE-1l
./download.sh
cd zaphfc

wget dondisperato.0catch.com/zaphfc_0.3.0-PRE-1f_florz-11.diff
patch < zaphfc_0.3.0-PRE-1f_florz-11.diff
cd ..

ln -s /usr/src/kernels/2.6.9-34.EL.i686 /usr/src/linux-2.6
ln -s /usr/src/kernels/2.6.9-34.EL.i686 /usr/src/linux

cd zaptel-1.2.6
make clean
make
make install
cd ..
cd libpri-1.2.3
make clean
make
make install
cd ..
cd zaphfc
- Mostra testo tra virgolette -
make clean
make

cp zaptel.conf /etc/zaptel.conf
——>yes<——- data-blogger-escaped-br=”br”>
nano /etc/rc.d/rc.local

at first add this line:

modprobe zaptel
insmod /usr/src/bristuff-0.3.0-PRE-1q/zaphfc/zaphfc.ko
sleep 10
ztcfg -vv

nano /etc/asterisk/zapata.conf

this is my zapata:

[channels]
language=it
switchtype=euroisdn
;If you connect to a hicom PBX set your ISDN Numbering Plan Identifier to unknown.
pridialplan=local
prilocaldialplan=local

signalling = bri_cpe_ptmp
;signalling = fxs_ks
rxwink=300

usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
rxgain=0.0
txgain=0.0
nationalprefix = 0
internationalprefix = 00
faxdetect=incoming
group=0
callgroup=1
pickupgroup=1
immediate=no

context=from-pstn
channel => 1-2

________________________________________
now you can recompile asterisk
cd /usr/src/bristuff-0.3.0-PRE-1q/asterisk-1.2.4
make clean
make
make install

reboot…
________________________________________

that’s all
donDisperato

A@h 2.7 with Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1l with “flortz” patch

how to install hfc card

 

after unload asterisk and amportal whit

amportal stop

 

type “setup”

unselect zaptel in system service…

and set the lan

 

—>reboot<— data-blogger-escaped-br=”br”>
cd /usr/src
wget http://www.junghanns.net/downloads/bristuff-0.3.0-PRE-1l.tar.gz
tar -zxvf bristuff-0.3.0-PRE-1l.tar.gz
cd bristuff-0.3.0-PRE-1l
./download.sh
cd zaphfc

wget dondisperato.0catch.com/zaphfc_0.3.0-PRE-1f_florz-11.diff
patch < zaphfc_0.3.0-PRE-1f_florz-11.diff
cd ..

ln -s /usr/src/2.6.9-22.EL /usr/src/linux-2.6
cd zaptel-1.2.3
make clean
make
make install
cd ..
cd libpri-1.2.2
make clean
make
make install
cd ..
cd zaphfc
make clean
make

cp zaptel.conf /etc/zaptel.conf
——>yes<——- data-blogger-escaped-br=”br”>
nano /etc/rc.d/rc.local

at first add this line:

modprobe zaptel
insmod /usr/src/bristuff-0.3.0-PRE-1l/zaphfc/zaphfc.ko
sleep 10
ztcfg -vv

nano /etc/asterisk/zapata.conf

this is my zapata:

[channels]
language=it
switchtype=euroisdn
;If you connect to a hicom PBX set your ISDN Numbering Plan Identifier to unknown.
pridialplan=local
prilocaldialplan=local

signalling = bri_cpe_ptmp
;signalling = fxs_ks
rxwink=300

usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
rxgain=0.0
txgain=0.0
nationalprefix = 0
internationalprefix = 00
faxdetect=incoming
group=0
callgroup=1
pickupgroup=1
immediate=yes
context=from-pstn
channel => 1-2

________________________________________
now you can recompile asterisk
cd /usr/src/bristuff-0.3.0-PRE-1l/asterisk-1.2.4
make clean
make
make install

reboot…
________________________________________

that’s all
donDisperato

A@h 2.5 with Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1l without flortz patch

how to install hfc card

 

after unload asterisk and amportal whit

amportal stop

 

type “setup”

unselect zaptel in system service…

and set the lan

 

—>reboot<— data-blogger-escaped-br=”br”>
cd /usr/src
wget http://www.junghanns.net/downloads/bristuff-0.3.0-PRE-1l.tar.gz
tar -zxvf bristuff-0.3.0-PRE-1l.tar.gz
cd bristuff-0.3.0-PRE-1l
./download.sh
ln -s /usr/src/2.6.9-22.EL /usr/src/linux-2.6
cd zaptel-1.2.3
make clean
make
make install
cd ..
cd libpri-1.2.2
make clean
make
make install
cd ..
cd zaphfc
make clean
make

cp zaptel.conf /etc/zaptel.conf
——>yes<——- data-blogger-escaped-br=”br”>
nano /etc/rc.d/rc.local

at first add this line:

modprobe zaptel
insmod /usr/src/bristuff-0.3.0-PRE-1l/zaphfc/zaphfc.ko
sleep 10
ztcfg -vv

nano /etc/asterisk/zapata.conf

this is my zapata:

[channels]
language=it
switchtype=euroisdn
;If you connect to a hicom PBX set your ISDN Numbering Plan Identifier to unknown.
pridialplan=local
prilocaldialplan=local

signalling = bri_cpe_ptmp
;signalling = fxs_ks
rxwink=300

usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
rxgain=0.0
txgain=0.0
nationalprefix = 0
internationalprefix = 00
faxdetect=incoming
group=0
callgroup=1
pickupgroup=1
immediate=yes
context=from-pstn
channel => 1-2

________________________________________
now you can recompile asterisk
cd /usr/src/bristuff-0.3.0-PRE-1l/asterisk-1.2.4
make clean
make
make install

reboot…
________________________________________

that’s all
donDisperato

asterisk@home 2.0 and HFC isdn

 

 

 

A@h 2.0

how to install hfc card

 

after unload asterisk and amportal whit

amportal stop

 

type “setup”

unselect zaptel in system service…

and set the lan

 

—>reboot<— data-blogger-escaped-br=”br”>
cd /usr/src
wget http://www.junghanns.net/downloads/bristuff-0.3.0-PRE-1.tar.gz
tar -zxvf bristuff-0.3.0-PRE-1.tar.gz
cd bristuff-0.3.0-PRE-1
./download.sh
cd zaphfc
ln -s /usr/src/kernels/2.6.9-22.EL-i686 /usr/src/linux-2.6
ln -s /usr/src/kernels/2.6.9-22.EL-i686 /usr/src/linux
cd ..
cd zaptel-1.2.0
make clean
make
make install
cd ..
cd libpri-1.2.0
make clean
make
make install
cd ..
cd zaphfc
make clean
make

cp zaptel.conf /etc/zaptel.conf
——>yes<——- data-blogger-escaped-br=”br”>
nano /etc/rc.d/rc.local

at first add this line:

modprobe zaptel
insmod /usr/src/bristuff-0.3.0-PRE-1/zaphfc/zaphfc.ko
sleep 10
ztcfg -vv

nano /etc/asterisk/zapata.conf

this is my zapata:

[channels]
language=it
switchtype=euroisdn
;If you connect to a hicom PBX set your ISDN Numbering Plan Identifier to unknown.
pridialplan=local
prilocaldialplan=local

signalling = bri_cpe_ptmp
;signalling = fxs_ks
rxwink=300

usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
rxgain=0.0
txgain=0.0
nationalprefix = 0
internationalprefix = 00
faxdetect=incoming
group=0
callgroup=1
pickupgroup=1
immediate=yes
context=from-pstn
channel => 1-2

________________________________________
now you can recompile asterisk
cd /usr/src/bristuff-0.3.0-PRE-1/asterisk-1.2.0
make clean
make
make install

reboot…
________________________________________

that’s all
donDisperato

Asterisk@home hfc isdn from dondisperato

A@h 1.3 – 1.5

how to install hfc card

 

after unload asterisk and amportal whit

amportal stop

 

type “setup”

unselect zaptel in system service…

and set the lan

 

—>reboot<— data-blogger-escaped-br=”br”>
cd /usr/src
wget http://www.junghanns.net/downloads/bristuff-0.2.0-RC8j.tar.gz
tar -zxvf bristuff-0.2.0-RC8j.tar.gz
cd bristuff-0.2.0-RC8j
./download.sh
cd zaphfc
wget http://zaphfc.florz.dyndns.org/zaphfc_0.2.0-RC8j_florz-8.diff.gz
gunzip -v zaphfc_0.2.0-RC8j_florz-8.diff.gz
patch < zaphfc_0.2.0-RC8j_florz-8.diff
ln -s /usr/src/linux-2.4.21-32.EL /usr/src/linux-2.4
ln -s /usr/src/linux-2.4.21-32.EL /usr/src/linux
cd ..
cd zaptel-1.0.9
make clean
make
make install
cd ..
cd libpri-1.0.9
make clean
make
make install
cd ..
cd zaphfc
make clean
make

cp zaptel.conf /etc/zaptel.conf
——>yes<——- data-blogger-escaped-br=”br”>
nano /etc/rc.d/rc.local

at first add this line:

modprobe zaptel
insmod /usr/src/bristuff-0.2.0-RC8j/zaphfc/zaphfc.o
ztcfg -vv

nano /etc/asterisk/zapata.conf

this is my zapata:

[channels]
language=it
switchtype=euroisdn
;If you connect to a hicom PBX set your ISDN Numbering Plan Identifier to unknown.
pridialplan=local
prilocaldialplan=local

signalling = bri_cpe_ptmp
;signalling = fxs_ks
rxwink=300

usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
rxgain=0.0
txgain=0.0
nationalprefix = 0
internationalprefix = 00
faxdetect=incoming
group=0
callgroup=1
pickupgroup=1
immediate=yes
context=from-pstn
channel => 1-2

________________________________________
now you can recompile asterisk
cd /usr/src/bristuff-0.2.0-RC8j/asterisk-1.0.9
make clean
make
make install

reboot…
________________________________________

that’s all
donDisperato